SpringSaver Installation Instructions

Installing SpringSaver

Why Install SpringSaver?

Lubricating your garage door springs is crucial for maintaining a smooth-running system and extending its lifespan. Here's a step-by-step guide on how to safely install SpringSaver to lubricate your springs.

Before You Begin

Tools and Materials:

  • SpringSaver (provided)
  • Spring Lubricant (provided)
  • Clean cloth or rag
  • Safety glasses
  • Protective gloves
  • Ladder
  • Scissors (use caution!)

Important Safety Information

  • Leave spring adjustments to professionals: Garage door springs and related hardware are under high tension and can cause serious injury if handled incorrectly. Only qualified professionals or mechanically experienced individuals should adjust them following the manufacturer's instructions.
  • California Proposition 65 Warning: This product may contain chemicals known to cause cancer, birth defects, or other reproductive harm.

Safety Precautions:

  • Ensure the door is closed and disconnected: Fully close the garage door and disconnect it from the automatic opener (refer to your opener's instructions for proper steps).
  • Disconnect power: Disconnect power to the automatic opener for added safety.
  • Wear safety gear: Protect your eyes with safety glasses and wear gloves to keep your hands clean and protected.

Step-by-Step Instructions:

  1. Inspect the Springs: Before lubrication, check the springs for any signs of damage, rust, or wear. If you notice significant issues, consult a professional for repairs or replacement. Verify there an inch or more of room for the SpringSaver wrap to rotate freely around the spring and not interfere with its surroundings. 
  2. Clean the Springs: Use a clean cloth to remove dirt, dust, or debris from the springs. This ensures the lubricant adheres properly.
  3. Measure the Spring: With the door closed and power off, measure the length of the spring you intend to cover (coil spring only, not the winding sleeves).
  4. Cut SpringSaver (if needed): If your SpringSaver doesn't match the measured length, lay it flat and cut it to the desired size using scissors (be cautious!).
  5. Apply Lubricant: Apply a 1/4" diameter bead of Spring Lubricant to the top side of the spring all the way across the full length of the spring. Lube color may vary. 
  6. Wrap the Spring: Lay the prepared SpringSaver wrap on the spring with the felt side facing down and the Velcro hook between the spring and wall. Let the hook portion of the velcro hang behind and below the spring. Lay the wrap onto the spring with the previously spread lubrication under the loop side of the velcro. Follow this by securing the hook and loop from the center outwards, keeping the sewing seam straight and even. The SpringSaver should be slightly loose and able to rotate freely around the length of the spring.  Once it is free to rotate on the entire length of the spring, loosely secure the fixed end of the spring with the zip tie provided. This will keep the wrap in place.
     
  7. Work in the Lubricant: Manually open and close the garage door several times to distribute the lubricant and ensure smooth operation.
  8. Wipe Excess Lubricant: Use a clean cloth to remove any excess lubricant that may have accumulated on the spring ends or other parts of the system.
  9. Multiple Springs (if applicable): Repeat steps 3-8 for all the springs on your door.
  10. Test the Door: Open and close the garage door a few times to confirm smooth operation and no unusual noises. Make sure the wrap is not too tight and binds up or twists.  If it does, loosen the velcro.
  11. Reconnect the Door (if applicable): Reconnect the garage door to the automatic opener if you disconnected it earlier.

Tips:

  • Not Too Tight: The wrap should not be tight to the spring. It should be free to spin around the spring freely.
  • If the SpringSaver Wrap Moves: If your SpringSaver wrap wants to migrate off the spring, simply use the zip tie provided on the inner end of the spring to secure the spring saver in place.
  • Regular Maintenance: Lubricate your garage door springs every six months as part of your routine maintenance. If you notice issues with the door's operation or unusual sounds, inspect and lubricate the springs as needed.
  • SpringSaver Trimming: After trimming the SpringSaver, some stitching might become exposed. This won't affect performance, but avoid pulling on the threads to prevent loosening the seams.

By following these steps, you can maintain the performance and longevity of your garage door springs, keeping your system running smoothly.